Click to shop ecu tuning       
All Water-Methanol Injection Controllers (15)DevilsOwn All DevilsOwn Parts
Water Methanol Injection Controllers - PLEASE SELECT YOUR VEHICLE IN THE UPPER LEFT
DevilsOwn Water Methanol Injection Controllers Zoom DevilsOwn

DevilsOwn Water Methanol Injection Controllers

The Progressive Controller from DevilsOwn is by far the latest technology this company has made thus far. This controller just so happens to be light weight and easy to install. It is designed to give your vehicle an increased pressure with a users adjustable range.

Controller General Operation:
  • Unit will read dial settings and calculate the slope of the progressive control.
  • Map voltage is read and converted to a boost value
  • Pump duty cycle is calculated based on dial settings and slope
  • When boost PSI reaches the START setting, the pump will come on with a 15% duty cycle
  • It will ramp up to 100% as boost approaches FULL setting.
  • The pump voltage percentage will increase with a 0.2 pound increase in boost. This means the voltage will step up 5 times over an increase of 1 PSI making a very linear response curve.


For ease of adjustment, each dial has 21 settings that are incremental. There is a setting for every hash mark and another setting in-between, each having the arrow close to a setting that will provide the exact setting.

For example, the 12 o'clock position on the START dial of a 2 BAR unit is a PSI setting of 7. It will also be a 7 if the arrow is 6 degrees to right (or left) of 12 o'clock once it is beyond half way to the middle of the setting which will be 7.5PSI. This allows the user to easily set the unit to exact values without having to be fussy with the dial for reference; the Dial settings for each version are as follows:

If the FULL setting is set to a lower PSI than the START setting, the start setting will be ignored. The pump will then switch on to 100% when PSI is above FULL setting. It will then switch off when it is below the FULL setting.

In order to prevent loading down the MAP sensor signal, the voltage input to the controller is left floating. This means that tapping into the stock MAP sensor that is connected to your cars computer will not affect the MAP voltage. However, if the MAP input wire (green) is left disconnected, sampled voltage will be erratic and therefore pump output voltage will be erratic.

LEDs:
  • RED - power led - It will be illuminated anytime there is power applied to the pink wire and the black wire is grounded.
  • GREEN - This led will light up proportional to pump output voltage, it will turn on dim and brighten as the pump reaches 100%
  • YELLOW - This is the Status led


On power up the unit will blink the yellow led indicating what BAR setting the unit is setup for.
  • 2 blinks is 2 BAR
  • 2 blinks & 1 fast blink 2.5 bar
  • 3 blinks is 3 BAR or voltage


During operation
  • It will come on solid in normal operation when the output voltage to pump is at 100%. It will stay on until output drops below 95% This prevents the light from fluttering if the boost is hovering around FULL. It will blink a steady rate when the unit is faulted to let you know if something is wrong.


Controller specs:
  • Input voltage 10-15v
  • Input current
  • Standby 60ma
  • 100% duty cycle 10A
  • Sensor input range 0-5v
  • PWM output 30hz
  • Duty Cycle 15%-100%


Universal DevilsOwn Water-Methanol Injection Controllers
Price
0-5 Volt$155.00  Add to Cart
2 Bar Map Sensor$155.00  Add to Cart
2.5 Bar Map Sensor$155.00  Add to Cart
3 Bar Map Sensor$155.00  Add to Cart
DVC-100$195.00  Add to Cart
DVC-30$175.00  Add to Cart
 
DevilsOwn Water-Methanol Injection Controller Reviews

This product has not yet been rated.  Write Review
 

Have you seen these Water-Methanol Injection Controllers?

Parts Available: 2004, 2001, 2002, 2003, 2007, 2006