Click to shop ecu tuning       

Testimonials (8,057)




2013NovOctSepAugJulMayAprMarFebJan
2012DecNovOctSepAugJulJunMayAprMarFebJan
2011DecNovOctSepAugJulJunMayAprMarFebJan
2010DecNovOctSepAugJulJunMayAprMarFebJan
2009DecNovOctSepAugJulJunMayAprMarFebJan
2008DecNovOctSepAugJulJunMayAprMarFebJan
2007DecNovOctSepAugJulJunMayAprMarFebJan
2006DecNovOctSepAugJulJunMayAprMarFebJan
2005DecNovOctSepAugJulJunMayAprMarFebJan
2004DecNovOctSepAugJulJunMayAprMarFebJan
Tyler Bollinger
02/25/2011
-----------------------------------
Best exhaust for hondas period hands down

Claudio Insaurralde
02/24/2011
-----------------------------------
It was a very good quality, normal install. I can only give it a 7 because, before purchasing, someone at H and R told me that it had a lifetime warranty, but when I received the product, the paperwork said 12 month warranty. I wish people who represent their company’s would know more about their products, and warrantee's. It is all good though because I like the results, and since it was already installed, I was not going to remove it.

Anthony Lumbi
02/23/2011
-----------------------------------
First you guys have outstanding Customer Service. Kirk you are the man!!! dude you worked with me and made everything happend from day one. It is difficult getting stateside items over to Okinawa but you helped get my Driveshaft here. It took a little longer than i expected but it was definetly worth the wait. Please continue to provide the support you guys do because in the states Customer Service is going by the waste side... Thanks again and i look forward to buying more parts from HPF!!

Anthony Lumbi
02/23/2011
-----------------------------------
Well first i have to say that this is a GREAT PRODUCT!!!! it replaced my two piece driveshaft out of my 180sx. I can honestly say that the driveshaft along with lightweight flywheel, and pullies helped my car out a ton...Quality of the welding is outstanding. I would recommend this to all that have never owned such a baller driveshaft hahahahaha.

Neil Caulfield
02/21/2011
-----------------------------------
added a noticable amount of power, was easy to install, and is of high quality.

Mike Beckers
02/18/2011
-----------------------------------
It is a nice piece. I am a little critical when installing parts. I port matched the manifold to a Proffesional Products throttle body. It was pretty close to matching, but this is 2 aftermarket parts, so that has to be taken into account. The upper intake manifold studs were a little short, so I had to get some hardware that was a little longer. Otherwise, the price for the part dcannot be beat. It is all install and running strong.

Roman Dominguez
02/16/2011
-----------------------------------
The rotors were great espcially along with the ebc brake pads (green stuff). At first it smelled and sqeeled for awhile but after a few days it went away. I mean it stops on a dime with no problems. I would recommend to anybody. Used on my 98 chevy cavalier LS

DEREK FRYMIRE
02/16/2011
-----------------------------------
These pads are awesome for the daily driver and weekend warrior. They are quiet and stop you good, where a seat-belt with these. My only downer and I know it is because of what the pads are for, but it does take a little warm up. So if you have been cruising on the high way for a little when you go to hit your brakes give it a couple taps to warm them up. On the track FLAWLESS for light weight under-power car.

DAVID MATLOCK
02/15/2011
-----------------------------------
My feelings echo what I wrote about the front bar, there are a few potential pitfalls that need to be (and may be) addressed in an instruction sheet we can all read. I'm giving the rear bar a slightly higher rating than I did the front because there were no clearance issues that required grinding or that the cross bar be in any particular orientation when tightened.

DAVID MATLOCK
02/15/2011
-----------------------------------
The parts themselves were high quality but there were a few issues, most could have been avoided with thorough documentation so my rating may (or may not) have been higher if the instructions had been available in English instead of Japanese only. Hood clearance is almost non-existent so it's critical the cross-bar be positioned with the smallest cross section in the near vertical orientation. There is a VERY small portion of the end bracket that contacted (and dented) the hood from the inside. That area can be ground away without harm. The end brackets are slotted and need to be aligned with each other carefully so the cross-bar isn't bound. Unless you are willing to omit both factory plastic covers, you will need to cut away some of the area around the end brackets so the larger plastic cover can be installed and the spare tire cover needs cut about 2/3 from the front and some small hinges fastened at that location. It's a nice piece and it really deserves a good installation manual.

Brandon Jostworth
02/15/2011
-----------------------------------
Strong clamps

Dennis Thomas
02/15/2011
-----------------------------------
best sound to come out of a 335i

Sylvan Shiner
02/12/2011
-----------------------------------
Good brake lines, ease to install.

Mike Beckers
02/10/2011
-----------------------------------
The price was unbeatable and as luck would have it, I needed one at the time. The only thiing to take in consideration when installin is that it uses the removable FIT Valve from Honda. I used a block off plate since I live in a warm climate. It fir perfectly and removing the FIT actually cleaned up the appearance of my engine bay. The throttle pulley works with an LS cable and LS or TYPE R cable mount perfectly. Fully closed to fully opened without any problem.

IMRAAZ AZIZ
02/10/2011
-----------------------------------
Perfect fit, physical sound quality. Yet to see how long it holds up for. Quiet performance.

Edward Morales
02/08/2011
-----------------------------------
Best thing I've ever bought. This Axles are strong, thick, and beefy! Micro balanced at 20,000 RPM who can go wrong choosing driveshaft shop for there axle upgrades!!

Daniel Schafer
02/03/2011
-----------------------------------
Installed on my 2000 civic si. Fit perfectly, exhaust tip looks good. Sound is not too loud, just deeper than stock. Says that it is stainless steel, but after 2 months looks like it has small corrosion spots. Overall I am very satisfied.

Neal Ruffino
02/02/2011
-----------------------------------
looks awesome

Penn Mohrman
02/02/2011
-----------------------------------
Kirk is the man, thanks for being so helpful and keeping me updated with everything....give him a raise! Haha keep up the good work HPF! Dynos will be posted shortly after I install the exhaust.

Evan Kelly
02/01/2011
-----------------------------------
Works great on my civic. If it had that mounting bracket welded on at the exit of the header it could have made things a bit more rigid. Good header though.